Changing your Jeep"s oil is a pretty basic job the anyone deserve to do at residence in the driveway. Law it yourself not only saves you a few bucks, but gives friend a possibility to visually inspect other points on her Jeep at the very same time. And when you perform it yourself, you deserve to rest easy knowing the task is done right and also with the exact parts or fluids of your choosing. Relying on your Jeep, even if it is you"ve mounted a lifted supsension or not, you may even have the ability to tackle this job without any type of jacks and jack stands or driveway ramps. And also is some instances you can also do this job without increasing your Jeep also if the suspension is totally stock. I"ll be making use of a lift, simply to do the job of taking photos easier, but really every you require for this job is a couple of hand tools.

You are watching: 2000 jeep grand cherokee oil capacity


What You will certainly Need


6 quarts that 5W-30 (Preferred) or 10W-30 (depending ~ above the temperature variety anticipated prior to your next oil change) Ratchet13mm SocketOil Filter SocketDrain PanShop Towels / record Towels--- not necessary - but valuable ---Rubber GlovesFunnel

Instructions


Before working on her Jeep, constantly park top top a level surface, put it in park and collection the parking break. It"s constantly a an excellent idea to chock the wheels to be extra for sure whenever working under your Jeep.

Before starting to adjust the oil, run the engine for a couple of minutes to warm the engine oil. This will aid the oil circulation easier and also quicker.

*

According come the owner"s manual, 5W-30 is the wanted oil because that both the 4.7L and the 4.7L High calculation engines and is ideal for ecological operating temperatures below 100ºF. If girlfriend live in one area that sees exterior temperatures end 100ºF then you have to use 10W-30.

*

1. Remove the oil filler lid to assist allow all the oil to drainpipe from the engine better.

*

2. Remove the oil filler baffle from inside the oil filler neck.

*

3. Using a 13mm socket, eliminate the drainpipe bolt indigenous the bottom the the oil pan.

*

4. Allow the oil to drain into a pan. Store some paper towels near by come clean up any kind of spills or drips and to wipe off any kind of oil that might splash onto your exhaust. After the oil has finished draining, change the drainpipe bolt and also torque to 25 ft lbs. (Hand tightening functions perfectly fine for the drain bolt if girlfriend don"t have a talk wrench.)

*

5. Using your oil filter wrench, eliminate the old oil filter.

*

The Mopar oil filter illustrates the steps for installing your new oil filter.

*

6. Clean and inspect the oil filter sealing surface ar to be sure there"s no corrosion or debris that may reason a bad seal ~ above the new filter.

*

7. Lubricate the seal on your brand-new oil filter with a couple of drops that clean engine oil.

*

8. Install the new filter on come the engine block. Hand tighten the filter.

*

9. Using one oil filter wrench, tighten the filter 1 more revolution past hand tight.

*

*

10. Using a funnel, refill the engine with oil. The 4.7L engine requires 6 Quarts that oil. If you"re using a 5 Quart jug, don"t forget to include one extr quart.

*

11. Clean off and re-install the oil filler baffle the you eliminated earlier.

*

12. Clean turn off the oil cap, climate lubricate the oil seal ~ above the cap with a few drops of clean motor oil. This will help make removing her oil cap during your next oil readjust much easier.

See more: How Far Is Las Vegas To San Diego, Ca, It'S 331 Miles From Las Vegas To San Diego

*

*

13. The overhead Electronic automobile Information facility or EVIC for brief keeps monitor of once it"s time to finish an oil change. Be sure to reset the service interval ~ completing your oil adjust so you"ll be reminded once it"s time to adjust it again. Through the Jeep in park (the key can it is in in the on position with or without the engine running) push the STEP button until the company message appears on screen. Then press and hold the RESET button for a few seconds. The EVIC will beep and also reset. The EVIC have the right to be programmed to different business intervals relying on your driving behavior by utilizing the MENU switch when the Jeep is in park.